Enquiry





I authorize Digisol to contact me. This will override registry on the NDNC.

captcha

DG-HR3420

ISSUE: How to Configure in 3G Mode?

STEP 1: ACCESSING THE WEB CONFIGURATION PAGE INSIDE THE ROUTER

– Access the configuration page using 192.168.1.1 in the address bar of the web browser
– Enter the username as admin and password as 1234 and click on Login.

STEP 2: CONFIGURE THE ROUTER IN 3G MODE
– Click on Setup > WAN > 3G.
– Select 3G WAN as Enable.
– Enter APN, Dial Number, User Name and Password provided by ISP.
– Click on Apply Changes.

STEP 3: CHECKING INTERNET STATUS
– If you are successfully connected to the internet, you will get numbers like 10.76.111.15
etc under WAN 3G Connections inside the IP Address and Gateway section.

Now verify the internet access through DG-HR3420 router.

ISSUE: How to Configure in Dynamic Mode

STEP 1: ACCESSING THE WEB CONFIGURATION PAGE INSIDE THE ROUTER

– Enter 192.168.1.1 in the address bar of the web browser. Press Enter.
– Enter the username as admin and password as 1234 and click on Login.

STEP 2: CONFIGURE THE ROUTER IN DYNAMIC MODE
– Click on Setup > WAN.
– Under WAN Configuration > Select WAN Mode as DHCP.
– Under MAC Clone > Select MAC From PC.
– Click on Apply Changes.

STEP 3: CHECKING INTERNET STATUS
– Click Status > Device Info.
– If you are successfully connected to the internet, you will get numbers like
114.35.54.56 etc under Ethernet WAN Interfaces inside the IP Address and
Gateway section.

Note: If you are using a modem to connect to the WAN port of the router and
if you are not getting any IP address under Ethernet WAN Interfaces, please
turn OFF the modem and router and turn them back ON after few seconds
respectively. Then check for the IP address.

Now verify the internet access through DG-HR3420 router.

ISSUE: How to Configure in PPPoE Mode (DSL)

STEP 1: ACCESSING THE WEB CONFIGURATION PAGE INSIDE THE ROUTER

– Enter 192.168.1.1 in the address bar of the web browser
– Press Enter
– Enter the username as admin and password as 1234 and click on Login

STEP 2: CONFIGURE THE ROUTER IN PPPOE MODE

– Click on Setup > WAN
– Under WAN Configuration, select WAN Mode as PPPoE
– Under PPP Settings, enter the username and password provided by your ISP in the UserName and the Password fields respectively.
– Under MAC Clone, select MAC From PC
– Click on Apply Changes

STEP 3: CHECKING INTERNET ACCESS

– Click Status > Device Info.

If you are successfully connected to the internet, you will get
numbers like 114.35.54.56 etc. under Ethernet WAN Interfaces inside the IP Address and
Gateway sections.

Now verify the internet access through DG-HR3420 router.

ISSUE: How to Configure in Static IP Mode?

STEP 1: ACCESSING THE WEB CONFIGURATION PAGE INSIDE THE ROUTER

– Enter 192.168.1.1 in the address bar of the web browser
– Press Enter
– Enter the username as admin and password as 1234 and click on Login.

STEP 2: CONFIGURE THE ROUTER IN STATIC IP MODE

– Click on Setup > WAN.
– Under WAN Configuration > Select WAN Mode as Static IP.
– Enter IP Address, Subnet Mask, Default Gateway and the DNS addresses provided by the ISP.
– Under WAN IP Settings, enter the IP address in Local IP Address Field. Enter the Subnet Mask in the NetMask field. Enter the Default Gateway in the Remote IP Address field.
– Under DNS Settings, select Set DNS Manually. Enter the DNS addresses provided by the ISP in the DNS 1 and DNS 2 fields respectively.
– Under MAC Clone, select MAC from PC.
– Click on Apply Changes.


STEP 3: CHECKING INTERNET STATUS

– Click Status > Device Info.

If you are successfully connected to the internet, you will get numbers like
123.122.25.62 etc under Ethernet WAN Interfaces inside the IP Address and
Gateway section with Protocol displayed as Static IP and the Status displayed as Up.

Now verify the internet access through DG-HR3420 router.

WhatsApp chat